Rear Sway Bar End Bracket Strap Kit – Powder Coated

$79.99

Rear Sway Bar End Bracket Kit

Qty 1 = 2 Strap Brackets & 2 Holding Clips

2 in stock

SKU: 171511433-Rear-Outer-Sway-Bar-Bracket-Kit Categories: , Brand:

Description

Rear Sway Bar End Bracket Kit

These NOS rear sway bar end bracket strap kits are Genuine Volkswagen parts. Refinished in silver powder coat to protect from corrosion and prolong longevity.

Fits Mk2 Scirocco  & Mk1 Scirocco S w/ Sway Bars. These can be installed on vehicles without sway bars, however, you must drill holes in your control arms.

Comes in with 2 to a kit – Left & Right – Qty 1 = 2 Strap Brackets & 2 Holding Clips.

#28 Bracket Part No: 171 511 433 / 171511433
#29 Clip Part No: 171 511 453 / 171511453

Installation:

  • Note the angled notch section on the bottom strap lip. This is the side you want to start inserting the clip.
  • Make sure your bracket is clocked in the direction that makes it easier to install.
  • Insert the clip tab onto the notched section first. See photo below (Front of Bracket Installed) This is the front install side.
  • The photo labeled “Rear of Bracket Installed” is how the rear of the bracket will look when your finished.
  • The best way to compress the strap for install is to use two large vice grips. Squeeze the strap down as far as you can and clamp on the vice grip.
  • Use the adjuster on the vice grip to tighten the jaw to further compress the strap as far as possible.
  • Pro Tip: You can remove the vice grip adjuster and replace it with a bolt so you can use a ratchet or wrench to compress the vice grip even more. If you have a large enough vice grip, you may not need two vice grips to install.
  • After that, use the other vice grip to compress do the same, compressing the strap a little more. Keep doing this back and forth with both vice grips until the bracket straps lips touch.
  • Then, with the tabbed side of the retaining clip, slide it on the notched end as best as far as possible.
  • Now, tap it slowly with a soft hammer until it’s seated 10mm and it feels line it will not fall off.
  • After that, then remove the vice grip.
  • Finally, you will then need to hit the clip fairly hard with a larger soft ended hammer to get it to seat all the way on. You can also use a soft piece of wood and a metal hammer. Support the back side with a piece of wood. It’s much easier if you have two people install this at the same time.
Rear Sway Bar Outer Bracket

Rear of Bracket Installed

Rear Sway Bar Outer Bracket

Front of Bracket Installed

 

 


Restore Your Classic Rear Cornering

Does your classic Volkswagen feel loose around tight corners? If so, your factory rear suspension hardware is likely failing. Over the decades, original steel brackets rust, bend, and completely snap. Consequently, your rear anti-roll bar detaches from your torsion beam axle. Therefore, your vintage car suffers from terrible body roll and sloppy handling. You absolutely need strong replacement hardware to fix this immediately. Our brand-new Rear Sway Bar End Bracket Kit is the perfect solution. Furthermore, replacing these broken mounts instantly restores your tight factory handling. Ultimately, you will finally enjoy carving canyon roads safely again. Stop dealing with an unstable and unpredictable rear suspension today.

Heavy-Duty Powder-Coated Steel Construction

First, this premium replacement kit utilizes thick, high-grade steel. Because of this, it easily withstands immense cornering forces and suspension loads. Additionally, the durable powder-coated finish strongly resists harsh road salt. As a result, you get a much longer lifespan than painted hardware. Furthermore, a fresh Rear Sway Bar End Bracket Kit keeps your suspension aligned. Conversely, cheap aftermarket brackets often bend or rust out quickly. Therefore, buying a powder-coated replacement part is the absolute smartest choice. Indeed, your classic rear axle will stay secure and quiet forever. You never want to risk sudden failure during spirited highway driving.

Perfect Fitment For Easy Installation

Next, this premium replacement kit perfectly fits your vintage A1 chassis. Specifically, it bolts directly onto your factory rear beam axle easily. Moreover, it features the exact dimensions to hold your sway bar tight. Therefore, you will never worry about sloppy fitment or frustrating clunks. Meanwhile, the entire installation process is incredibly fast and stress-free. You simply unbolt the old rusted brackets from your rear suspension. Then, you bolt these brand-new units directly into the factory location. As a consequence, absolutely anyone can safely complete this crucial repair underneath. It truly is a fast and rewarding weekend garage project.

Essential Preventative Suspension Maintenance

Finally, keeping your classic rear suspension completely secured is critical. A broken bracket quickly ruins the handling balance of your car. Accordingly, replacing rusty metal mounts right now prevents dangerous oversteer. Thus, investing in a fresh Rear Sway Bar End Bracket Kit is smart. We highly recommend inspecting your rubber sway bar bushings simultaneously. Usually, if your metal brackets are snapped, your rubber is ruined. Replacing everything together guarantees your entire rear suspension functions like new. In conclusion, stop letting bad handling ruin your beautiful restoration project. Buy your new powder-coated brackets today and drive with confidence!

Additional information

Weight .82 lbs
Dimensions 5 × 3 × 2 in

You may also like…